At the dawn of the tackle for the “long cast” in building a float snap-in, there were a lot of experiments on the use of moving floats with two points of attachment on the fishing line. The result was that it is inconvenient and not necessary.
With floats with two points of attachment all too often tooling salesthese during the flight and, what’s worse, it is almost impossible to sink the line between float and rod. But floats left and they are successfully used in the Bologna tackle. However, there is still a good example of their effective application.
Let’s pretend we’re on the Volga reservoir in the day. Due to the reduction of water discharge from hydroelectric dams the flow becomes weaker, and at some point, the water movement stops. The level decreases and fish departs from coast. Casting distance becomes inaccessible to the feeder, so you need a boat. With the boat in most cases is caught using the same feeder, on the side rods, as well as using the time tested certain variations of Koltsovo” and “springs”. But when the current is very weak, requires casting at least for some distance from the boat. If you omit the bottom-snap vertically, the inevitable twisting of the leash. You can, of course, to make snap, devoid of this drawback, for example, end-load, but there is another nuisance. On low for bait washed out of the trough very slowly, and to wait the approach of the fish until Monday. Based on these conditions, you need to make the easy bait, and tackle to increase the area of harvest.
There is another important factor — bite “weak”, and sensitivity of on-Board equipment may become insufficient. And if there will be the excitement of the water and pitching of the boat, the catch will be very inefficient. Exit float in a snap.
Because depth of fishing is decent, you definitely need a sliding float. I believe that even at a depth of 6 m there is no sense of strain with long mahovym rod and a stationary snap-in. The rod may be a match or even feeder with a length of 3-4 m. Very short rod is not very convenient, since sometimes you have to look for a stream on which you want to put snap and run from the stern to the nose is not very convenient. The jet in this case is not as important as the profile of the bottom under the boat. Catch has the meaning at the edge or around it.
From the coils is instantaneous, although they also catch can. The same applies to multiples. Inertial model with a big drum in this case does not have such obvious advantages, as quite a strong current. In our case, the current can be so weak that the snap will not pull the fishing line even with a good coil. In any case, you have to play off line from the reel with your free hand. The inertial reel is good that guarantees fast and, most importantly, hard cutting.
The design of the snap-in — sliding float with two attachment points on the line. In my opinion, it makes no sense to pay attention to the difference in body shape of these floats. If the current is weak, manipulation of equipment, and it is mostly or inhibition of sailing, up to a full stop at some point, or twitching and pulling towards themselves, do not lead to the loss of stability of the float. It is important to properly ohrozit.
Personally, I began to use floats one, now well-known Italian company. This manufacturer floats with two points of attachment on the line in all three forms, and I don’t see any difference in their functionality (pictured). Whichever the like.
In my opinion, well, that antenna have its own buoyancy. It is always good when in the process of catching, a set of baits that differ in weight. Initially, the float gruzitsja so that under the water was all body, and even the part of the antenna.
When you change a light bait on a heavier float will ogroats below, but not sinking due to the buoyancy of the antenna. Of course, it happens that the lug worm along the bottom or even anchoring snap the bait on the hook leads to flooding of the float. In such cases, it is easiest to remove one of the lightest weights with snap.
Distribution shipping is for a very simple scheme — one primary sinker and was divided into three or four parts. This design is optimal, based on the set of transactions that are commonly used.
Because depth of fishing is big, suggest to use as the main sinkers stationary olives. It is stationary, which is fixed on the fishing line two silicone kembrikom. Moving the olive in this case worse because it requires more complex fixing and the current was very weak and the twisting of the fishing line while sailing there. I use olives of the same company from a tungsten alloy. Unlike lead olives, tungsten flush snap-in is noticeably faster, which is critical.
Quite difficult something specific in advance to advise of the thickness of the line. The thinner line is, the closer to vertical you can lower the bait to the point of starting the transaction. This is very important if you are using bait. Often, almost all bites occur at a distance of one meter from lying on the bottom of the bait. I use the basic scaffold not thicker than 0.14 mm, and for leash take 0,09-0,11. With the exception of cases when it comes to carp — there you have to change all the attachments.
Hook matched to the size of the bait, but unlike snap-ins for the primaries of the rod or plug, the size of the hook a few more. Very important parameter is the own weight of the hook, especially if you use transactions with the inhibition of sailing snap or hold in place. These transactions effective when fishing for roach and white bream. But the main object is usually bream, and then fishing technique more simple. You can catch the principle of “running” donkey, that is, to survey a large area in search of active fish. Bait is not required, so fishing is very active, with a study of various deep and interesting as its topography. Here is helping the sounder. After the detection of the active fish you can get “on point” to lure and continue fishing. While hunting for bream this tactics is justified. It is possible to immediately determine the place of fishing, put the boat in a banner on the two anchors and to start complementary feeding.
As for poorly blurs the bait, I use a large “winter” feeder, which takes the “easy” blend to the point of beginning sailing snap. It makes sense to lower the feeder with a short powerful rod with a reel. In this case, it will be convenient to omit the snap, not the side of the boat, and at some distance. Enough to start approximately one kilogram of dry bait. In it, I add a little chopped worm and a handful of maggots. It is good to add a handful of millet porridge, which will keep the bream, when he comes to the bait. You can initially deliver to the bottom and more food, but only if it is assumed that the flow will increase.
As for the equipment transaction, then in most cases the bait dragging the bottom. If bites are rare and occur in one and the same point, it makes sense to try to anchor the snap-in at this point, the herdsman. For this reason I share shepherd boy into several parts, to be able to increase or decrease the part that lies on the bottom. Very effective could be the retention snap on the point of bites, but in this case I advise you to increase the length of the leash. Length is chosen each time experimentally and can reach five feet. With a long leash good transactions with periodic stops sailing and is released in free swimming.
Experiment with posting, and snap design makes sense not only to the beginning of bites, but when they become rare.
As for bait, then, for example, on the Volga, I almost always use the worm. A lot less success bring other baits such as maggot, paste or “pasta”, although it is necessary to try.
The fishing is very interesting, especially in the uncool the days of weak currents, quiet weather and summer heat. This method can be used everywhere where the current is weak, and the depth is large.
